Ratgeber
Wiring a Terminal Block on MP-C
You wire the terminal blocks installed on the MP-C to connect I/O devices and power.
The MP-C can be installed on a DIN rail or other flat surface inside a cabinet. The device is recommended to be installed in a cabinet, unless local regulations allow an exception.
A DIN rail is a common and convenient technique for installing the MP-C along with other associated control and monitoring devices. The most efficient ventilation is achieved with the wall-mounted DIN rail oriented horizontally and with adequate space provided between the MP-C rail and adjacent rails or other devices.
The MP-C is typically installed horizontally (on a DIN rail going from left to right), with the device label text in the upright position reading left to right.
The restrictions on installing the device in other orientations differ depending on the operating conditions.
Under normal operating conditions of 0 to 50 °C (32 to 122 °F), the MP-C can be installed in the following orientations:
Horizontally (on a DIN rail going from left to right), with the device label text in the upright position reading left to right. See “a” in the following figure.
Vertically (on a DIN rail going from top to bottom), which means that the device is rotated +90 degrees or -90 degrees from the horizontal position. See “b” and “c” in the following figure.
Installing the MP-C rotated 180 degrees from the horizontal position with device label text up and down (“e” in the figure), face down from a ceiling (“d” in the figure), or face up on a horizontal surface (“f” in the figure) is not supported.
When the MP-C is used for rooftop applications, -40 to +60 °C (-40 to +140 °F), the device should be installed horizontally, with the device label text in the upright position reading left to right. See “a” in the following figure. Any other installation orientation (“b”, “c”, “d”, “e”, and “f” in the figure) may exceed the controller's thermal specifications, which can damage the controller.
All MP-C controller models are recommended to be installed in a cabinet, unless local regulations allow an exception.
The device should be installed within an enclosure such as a control cabinet for isolation to exposed live parts.
The MP-C can be installed in a standard DIN enclosure/cabinet.
When installing MP-Cs in a cabinet, it is recommended to provide ample space between the DIN rails and controllers for sufficient ventilation.
To help prevent the device from sliding down or sideways on the DIN rail, install an end clip for DIN 35 (part number SXWDINEND10001) tightly against the bottom or rightmost device on the rail. The end clip is easily removed if you bend the snap lock open with a screwdriver.
The MP-C is delivered with terminal blocks installed on the device. Spare terminal blocks can be ordered separately using the part number SXWMPCCON10001.
The terminal blocks are removable. You can replace an MP-C in seconds because no terminal wiring is affected. The only exception is the high power relay outputs on the MP-C-15A and MP-C-18A models, which use a two-position fixed terminal block due to current requirements.
All MP-C models can be equipped with MP-C Display (part number SXWMPCDSP10001), which is an add-on module that enables manual override control of analog and digital outputs. The module consists of an LCD display and keys. The module is designed for permanent installation.
Do not try to remove the MP-C Display module as it may damage the enclosure and the module. Once installed, the MP-C Display module cannot be removed.
Gefahr
|
|---|
|
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH De-energize the high-voltage equipment connected to the relay outputs before wiring. More than one disconnect switch may be required to de-energize the equipment. Failure to follow these instructions will result in death or serious injury. |
Vorsicht
|
|---|
|
RISK OF ELECTRIC SHOCK Disconnect the 24 VAC/DC power supply and other electrically powered equipment before wiring. Failure to follow these instructions can result in injury or equipment damage. |
De-energize the high-voltage equipment connected to the relay outputs of the controller.
This applies to all MP-C controllers except the MP-C-18B model, which does not have relay outputs.
Disconnect the 24 VAC/DC power supply and other electrically powered equipment that is connected to the controller.
Ensure that the correct terminal block is used and that it is properly installed on the MP-C. Für weitere Informationen siehe Installing a Terminal Block on MP-C .
Loosen the screws of the terminal block.
Strip approximately 7 mm (0.3 inch) of the insulation from the end of each wire.
Insert the stripped end of each wire fully into its intended terminal. Ensure that no bare wire strands extend from the terminal.
Tighten the screws using a small flat-blade screwdriver. Ensure that the screws are fully tightened. Use the following recommended screw tightening torque: 0.56 Nm (5 lbf.in).
MP-C Device Installation
MP-C Screw Terminals
MP-C-15A Screw Terminals
MP-C-18A Screw Terminals
MP-C-18B Screw Terminals
MP-C-24A Screw Terminals
MP-C-36A Screw Terminals
Wiring
Installing a Terminal Block on MP-C
Removing a Terminal Block from MP-C
Powering Up MP-C