Automation Servers

An Automation Server is a Schneider Electric manufactured embedded device that generally serves as the lowest tier SmartStruxure server within the SmartStruxure solution. The Automation Server controls and supervises equipment, typically HVAC equipment. The Automation Server uses I/O modules with connected field devices, such as sensors and actuators, to do that.

Automation Server is based on the patented two-piece design. Each Automation Server consists of an electronics module and a terminal base.

The Automation Server is installed with the I/O modules on DIN rails in cabinets. The Automation Server electronics module uses a W1 enclosure. Power is supplied through the terminal base backplane.

Electronics Modules

The electronics module is the main component of SmartStruxure devices that are based on the patented two-piece design. The electronics module is installed on a terminal base, which constitutes the second component of the device.

Para obtener más información, consulte Electronics Modules .

Terminal Bases

The terminal bases are used for SmartStruxure devices that are based on the patented two-piece design. The terminal base provides the I/O bus to the electronics module installed on the terminal base as well as to the SmartStruxure device installed to the right (next terminal base in the chain).

Para obtener más información, consulte Terminal Bases .

Memory

The Automation Server has two types of memory:

128 MB SDRAM (for program execution)
4 GB flash (for storage)

If a power failure occurs, all important variables are automatically saved to the flash memory before complete shutdown. When power returns, this data retention function ensures that the Automation Server can continue to run with the correct set of values.

Supported Building Standards

The Automation Server natively communicates with three of the most popular communication protocols:

BACnet: The Automation Server directly communicates to BACnet/IP and BACnet MS/TP networks, which provides access to b3 devices and BACnet devices.
LonWorks: The Automation Server has a built-in FTT-10 port, which enables access to Xenta devices and LonWorks devices.
Modbus: The Automation Server natively integrates Modbus RS-485 master and slave configurations, as well as IP client and server. This integration provides access to devices that communicate on the Modbus protocol, such as power meters, circuit breakers, and lighting controllers.

Automation Server Communication Ports

The Automation Server has the following communication ports:

1 Ethernet 10/100 megabit port
2 RS-485 ports
2 LonWorks (TP/FT and RS-485) ports
2 USB host ports
1 USB device port
1 backplane I/O bus port

Para obtener más información, consulte Automation Server Communication Ports .

Reset Functions

There are three different types of reset for the SmartStruxure server devices: warm start, cold start, and DFU mode. Depending on the type of reset, the SmartStruxure server device can be reset using the reset button or a command from WorkStation.

Para obtener más información, consulte Reset Functions .

Communication Port Wiring

The wiring recommendations for the SmartStruxure server device communication ports apply to the wires and cables used for RS-485 communications, LonWorks communications, USB connections, and Ethernet connections. Always use the recommended cables and wires.

Para obtener más información, consulte Communication Port Wiring .

SmartStruxure Server Device Replacement Using Restore

Backup and Restore assures that SmartStruxure server devices data can be restored to a replacement SmartStruxure server device in the event of hardware failure, or to the same SmartStruxure server device in the event of data loss. As a precaution, you back up your SmartStruxure server devices regularly so that you can use the most current backup to restore the SmartStruxure server devices data to a replacement SmartStruxure server device. You also configure the new SmartStruxure server device to match the name and the network settings of the replaced SmartStruxure server device so the system can identify this SmartStruxure server device when online.

Para obtener más información, consulte SmartStruxure Server Device Replacement Using Restore .

Especificaciones

Electrical
DC input supply power	7 W
DC input supply voltage	24 VDC
Environment
Ambient temperature, operating	0 to 50 °C (32 to 122 °F)
Ambient temperature, storage	-20 to +70 °C (-4 to +158 °F)
Maximum humidity	95 % RH non-condensing
Material
Plastic rating	UL94-5VB
Enclosure	PC/ABS
Enclosure rating	IP 20
Mechanical
Dimensions including terminal base	90 W x 114 H x 64 D mm (3.6 W x 4.5 H x 2.5 D in.)
action_zoom_plus_stroke
Weight including terminal base	0.294 kg (0.65 lb)
Weight excluding terminal base	0.194 kg (0.43 lb)
Real-time clock backup
Inaccuracy, at 25 °C (77 °F)	-47 to +73 seconds per month
Backup time	30 days
Communication ports
Ethernet	10/100BASE-TX RJ45
USB	1 device port (type-B) and 2 host ports (type-A)
RS-485	Dual 2-wire ports, bias 3.3 VDC
LonWorks	TP/FT-10
Communications
BACnet	BACnet/IP and MS/TP, port configurable, default 47808
	BTL B-BC (BACnet Building Controller) ^a
	BTL B-OWS (BACnet Operator Workstation) ^a
a) See the BTL Product Catalog for up-to-date details on BTL listed firmware revisions on BACnet International's home page.
Modbus	Modbus TCP, client and server
	Serial, RS-485, master or slave
TCP	Binary, port fixed, 4444
HTTP	Non-binary, port configurable, default 80
HTTPS	Encrypted supporting TLS 1.2, 1.1, and 1.0, port configurable default 443
SMTP	Email sending, port configurable, default 25
SNMP	version 3
	Network supervision using poll and trap
	Application alarm distribution using trap
LNS
LNS version	OpenLNS
	Installed on WorkStation PC
LonMark
Resource files version	14.00
CPU
Frequency	160 MHz
Type	AT91RM9200, ARM9 core
SDRAM	128 MB
Flash memory	4 GB

Internal Configuration

All connectors of the Automation Server, except for the Ethernet connector, refer to signal ground as shown in the figure below.

action_zoom_plus_stroke

Figura: Automation Server internal configuration

The I/O bus in the terminal base provides the Automation Server with power and an address.

The address value in the I/O bus is increased by one for each terminal base. The I/O bus also enables RS-485 communication between the I/O module and the SmartStruxure server device.

Funcionalidad

Productos

Explicación de procesos